HAZER-HZ2
Haze Machine User Manual
160.450UK
User Manual – Hazer HZ-2 160.450UK
2
Hazer HZ-2 Haze Machine – For indoor use only
1. General Introduction :
A professional haze machine that is the ultimate in fine mist generation.
This unit can quickly and smoothly develop a pre-determined level of haze
and maintain it consistently by the hand controller provided.
Features :
2,400 CU Ft (68m³) per minute
Relay temperature controlled for constant temperature control and
longer life span
Uniquely designed nozzle for reduced condensation build up in the
pipes
True constant haze output
Variable output angle
Low fluid indicator
Timer output remote control included
Easy to transport and portable
2 Channel DMX (output level and fan speed)
Removable tank for easy maintenance
Recommended QTX Light High grade haze fluid for use with this
machine
Caution! Please read this manual carefully before
operating! Damage caused by misuse
is not covered by the warranty!
User Manual – Hazer HZ-2 160.450UK
11
15. Technical specification :
Power supply 230Vac, 50Hz
Fuse F5A
Power 600W
Re-heat time 4 min (approx)
Haze Output 2,000 Cu Ft (283m³) per minute
Tank capacity 1.2 Litres
Dimensions 220 x 205 x 490mm
Weight 7.6kg
14. Disposal :
Please disposal of the unserviceable device according to the current
statutory requirements.
User Manual – Hazer HZ-2 160.450UK
10
11. DMX controlling:
DMX channel DMX Scale Detail function
CH 1 000 - 255 0% - 100% Haze output
CH 2 000 - 255 0% - 100% Fan speed
Dip Switch addressing
To set the DMX address please see the example table below and for more details
visit the QTX website www.qtxlight.com
(Note: 1 = On, 0 = Off)
DIP Switches
DMX Address
1 2 3 4 5 6 7 8 6
1 0 0 0 0 0 0 0 0 1
2 0 0 0 0 0 0 0 1 0
3 0 0 0 0 0 0 0 1 1
… .. .. .. .. .. .. .. .. ..
509 1 1 1 1 1 1 1 0 1
User Manual – Hazer HZ-2 160.450UK
3
2. Package Contents :
Please check the contents to ensure that the product has been received in
good condition.
Hazer HZ-2 Haze Machine x 1pcs User’s Guide x 1pcs
Power Cord x 1pcs Remote control x 1pcs
If you find any accessory is missing or the machine has arrived with any
problems, please contact your local dealer at once. Do not try to fix this item
yourself or you will lose the warranty. Please keep the original package and
invoice for any possible replacement or returned demand.
3. Recommended Fluid:
For the Hazer-FX1000 haze machine we strongly recommend the following
fluid which has been specifically formulated to perform best with any
heater based haze machines.
QTX Ref
Code
Description Size Results
160.590UK 1 Litre
160.591UK
High quality
professional Haze fluid
5 Litre
High quality
ultra fine mist
User Manual – Hazer HZ-2 160.450UK
4
4. Setup :
1. Unpack the haze machine
2. Unscrew the top cap of the tank and remove to fill with the
recommended haze fluid
3. Replace the bottle and screw the cap securely ensuring the pipe is
fed down to the bottom of the bottle so a consistent flow of fluid is
supplied to the machine
4. Connect the remote control
5. Connect the IEC mains plug and power up
6. Heat up time is usually between 3-6 minutes. Please ensure no
button is pressed during the heat up time. When the machine is
ready the LED light on the machine and remote control will
illuminate
7. Press the button on the remote control for 5 seconds so the fluid has
a chance to flow through the heater block making it ready to use..
8. After this you will be able to use the haze machine. It is
recommended to produce haze with small pauses in between so that
the temperature is maintained and the thermostat doesn’t switch
off.
User Manual – Hazer HZ-2 160.450UK
9
11. Timer controller:
1) Timer on/off button
2) Continuous output
3) Manual override button
4) Timer LED indicator (Illuminated Yellow when timer active)
5) Manual ready indicator (Illuminates Green when ready)
6) Power indicator (Illuminates red when power is on)
7) Adjust the amount of Haze released (between 0 – 100%)
NOTE: The below controls are only used when in timer mode
8) Adjust the interval gap between each release of Haze (between
0 – 30 Min approximately)
9) Adjust the duration the Haze / Haze is released at each interval
(between 0 – 15 seconds approximately)
For best results select “continuous” and adjust output to achieve
desired effect, note it can take around 30 seconds for the machine
to produce the correct output.
User Manual – Hazer HZ-2 160.450UK
8
11. Layout:
1) IEC Power socket
2) Fuse holder
3) Power switch On/Off
4) Back door (Removable fluid tank inside)
5) Remote control
6) DMX In
7) DMX Out
8) No fluid indicator
9) Ready indicator
10) Dip switches for DMX address
11) DMX indicator
User Manual – Hazer HZ-2 160.450UK
5
10. Mounting instruction :
The fixture may be mounted in any position provided there is adequate
room for ventilation and the fluid can not leak.
It is important never to obstruct the front of the machine, fan or vents
pathway. Mount the fixture using a clamp.
Adjust angle of the fixture loosening both knobs and tilting the fixture.
After finding desired position, re-tighten both knobs.
When selecting installation location, take into consideration refilling the
tank and routine maintenance. Safety cables must always be used.
Never mount in places where the fixture will be exposed to rain, high
humidity, extreme temperatures changes or restricted ventilation.
5. Caution! To prevent Mortal Electrical Risk and Long Life Operation :
For your safety, please kindly pay attention to all of the warnings listed
below:
Always plug in the power plug last and disconnect from the mains
when the device is not in use or before cleaning.
Do not install and operate the device in rain or extreme heat,
moisture or dusty environments.
This device is for indoor use only and in a dry environment.
Do not switch on immediately but wait until it reaches to room
temperature if the device has been exposed to drastic temperature
fluctuations.
Do not shake the device and avoid brute force when installing or
operating
Do not use the device during thunderstorms and please disconnect
the power.
User Manual – Hazer HZ-2 160.450UK
6
Do not use solvents or aggressive detergent to clean the device. Use
a soft and clean cloth.
Do not modify the device or the connected power cord without
authorization.
Use appropriate safety-rope for safety.
Clean the machine regularly using water or smoke/haze cleaning fluid
(160.670)
6. Connect with power supply - The ground wire must be connected :
Use the plug to connect to the main power supply as following.
Wire Connection International signal
Brown Live L
Blue Neutral N
Yellow /Cyan Earth
7. Quick Trouble Shooting :
If the unit is not functioning properly
7.1 Check if main power is on and fuse hasn’t blown
7.2 The remote control is plugged in correctly in to the socket
7.3 Check there is fluid in the tank
7.4 Check that the pipe is pushed down to the bottom of the tank
7.5 Check the correct fluid has been used.
7.6 If there is a block use distilled water or haze machine cleaning fluid.
User Manual – Hazer HZ-2 160.450UK
7
8. Replacing Fuse :
Disconnect from the main power supply first, then remove the fuse holder
above the IEC Socket to reveal the fuse. Replace the correct fuse rating as
stated on lighting or user guide. Then, lock the fuse holder cover back into
place.
9. General Maintenance :
To maintain optimum performance and minimize wear, the item should be
cleaned frequently. Usage and environment are contributing factors in
determining frequency. As a general rule, fixtures should be cleaned after
use to avoid dust build-up and blockages. Which can result in poor
performances, overheating and breakages. Be sure to power off fixture
before conducting maintenance.
Unplug fixture from power. Use a vacuum or air compressor and a soft
brush to remove dust collected on external vents and internal components.
Clean the external case when the fixture is cold with a dry cloth or tissue,
and drag dirt and grime to the outside case.
To ensure a continuing high performance it is recommended to use water
or haze cleaning fluid (160.670) to clean the internal workings. Simply
empty the tank of any haze fluid. Fill with water or haze cleaning fluid then
operate two full cycles to clean the internal pipes this should be done once
every 2 months to ensure continuing high performance
